- #CRATE AMPLIFIER REPAIR PARTS DRIVERS#
- #CRATE AMPLIFIER REPAIR PARTS PRO#
- #CRATE AMPLIFIER REPAIR PARTS SERIES#
With built-in lock washer to keep the screwĪnd nut from loosening. Used to connect a ground wire to a screw and nut on a chassis. Made from tin-plated brass - will not rust. Theseĭampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5.
Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Will withstand high temperatures of pre-amp tubes, reusable when you change An economical alternative to more expensive tube dampers. Use two (or three) of these rings around a pre-amp tube to reduce noise and Spring in top of shield fits over the tube.įits 12AX7A and similarly sized preamp tubes. TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, Shield and base only - socket not included. Replacement for Ampeg,Ĭrate and many other brands. Fits 12AX7A and similarly sized preamp tubes. Spring in top of shield which fits over the TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL. Replacement for Fender™ and many other brands. WITH 9-PIN TUBE SOCKET AND INTEGRAL TUBE SHIELD BASE. TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL LARGE TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6550 OR KT-88 TUBES. TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR E元4. Fit the AL-921 Ampeg logo, and the Fender
Used on modern Ampeg Speaker Cabinets, this 3 inch x 4 inch plastic logo isĪffordably priced. L-pad is rated at 100 watts RMS, is designed to be used with 16 ohm loads,
#CRATE AMPLIFIER REPAIR PARTS DRIVERS#
Use with 8 ohm speakers, horn drivers or tweeters. May also be used with the LFP-380 face plate and knob. L-PAD, 16 Ohms, 3/8" threaded bushing (3/8" long), with plate, knob and hardware. Style of L-Pad is found on many popular bass cabinets to control the L-pad is rated at 100 watts RMS, is designed to be used with 8 ohm loads,įeatures a 3/8" shaft length, and comes with mounting hardware.
#CRATE AMPLIFIER REPAIR PARTS SERIES#
Resistance in series and parallel, keeping impedance a constant 8 ohm load. L-pads adjust the relative volume of drivers connected to them by placing added for use with 8 ohm speakers, horn drivers or tweeters. L-PAD, 8 Ohms, 3/8" threaded bushing (3/8" long), with plate, knob and hardware. 3 1/8 inches inĭiameter, 7/8 inch depth into cabinet. Raised lettering in charcoal gray instead of white. This is the face plate and knob only - L-PAD itself ordered separately.
#CRATE AMPLIFIER REPAIR PARTS PRO#
Face plate AND knob only! L-Pad ordered separately.Ĭabinets including the SWR Goliath, Marcus Miller Golight 410, WorkingmanĨx10, Working Pro 2x10, Ampeg PN-210HLF, PN-410HLF, SVT-410HLF, SVT-610HLF,īXT410HL4, PR-1528HE, PN-115HLF, PR-810H, PB-250, the Kustom G410H, the
L-PAD FACE PLATE AND KNOB, for 3/8" diameter threaded bushing found on most L-Pad LevelĬontrols. Turn-on), very high dark resistance (50 M Ohm). 100dB dynamic range, fast response (2.5ms Used in many Mesa-Boogie and Crate models in the channel Replaces VTL5C1 from Vactec or Excelitas at anĪffordable price. AC Power Items Reverb Tanks Switches Relays Fans
0 kommentar(er)
